mirror of
https://github.com/armbian/build
synced 2025-09-24 19:47:06 +07:00
Merge pull request #4778 from schwar3kat/Tweak-orangepi-r1plus-lts-LEDs-and-networking
Tweak orangepi-r1plus-lts LEDs and networking.
This commit is contained in:
schwar3kat
@@ -4,8 +4,63 @@ BOARDFAMILY="rockchip64"
|
||||
BOOTCONFIG="orangepi_r1_plus_lts_rk3328_defconfig"
|
||||
KERNEL_TARGET="current,edge"
|
||||
DEFAULT_CONSOLE="serial"
|
||||
MODULES="g_serial"
|
||||
MODULES="g_serial ledtrig_netdev"
|
||||
MODULES_BLACKLIST="rockchipdrm analogix_dp dw_mipi_dsi dw_hdmi gpu_sched lima hantro_vpu"
|
||||
SERIALCON="ttyS2:1500000,ttyGS0"
|
||||
HAS_VIDEO_OUTPUT="no"
|
||||
BOOT_FDT_FILE="rockchip/rk3328-orangepi-r1-plus-lts.dtb"
|
||||
|
||||
# SYS-TRIGGERED LEDs:
|
||||
|
||||
# NOTE: If LED funcionality is hard coded into an Armbian service for a board or family, it may override one or more of these settings.
|
||||
# This will add a file /etc/armbian-leds.conf to the build to configure the three board LEDs.
|
||||
# Green lan LED will flicker on lan0 RX. Green eth LED will flicker on eth0 RX.
|
||||
# Red status led will display heartbeat pattern.
|
||||
# For netdev trigger to work, ledtrig-netdev must be enabled in kernel.
|
||||
# either in the board config file: e.g. MODULES="...,ledtrig_netdev"
|
||||
# or in the family config file: e.g. CONFIG_LEDS_TRIGGER_NETDEV=y in linux-rockchip64-current.config
|
||||
|
||||
# Content:
|
||||
function post_family_tweaks_bsp__enable_leds_orangepi_r1_plus_lts() {
|
||||
display_alert "Creating board support LEDs config for orangepi-r1-plus-lts"
|
||||
cat <<- EOF > "${destination}"/etc/armbian-leds.conf
|
||||
[/sys/class/leds/orangepi-r1-plus-lts:green:lan]
|
||||
trigger=netdev
|
||||
interval=52
|
||||
brightness=1
|
||||
link=1
|
||||
tx=0
|
||||
rx=1
|
||||
device_name=eth0
|
||||
|
||||
[/sys/class/leds/orangepi-r1-plus-lts:green:wan]
|
||||
trigger=netdev
|
||||
interval=52
|
||||
brightness=1
|
||||
link=1
|
||||
tx=0
|
||||
rx=1
|
||||
device_name=lan0
|
||||
|
||||
[/sys/class/leds/orangepi-r1-plus-lts:red:status]
|
||||
trigger=heartbeat
|
||||
brightness=0
|
||||
invert=0
|
||||
EOF
|
||||
|
||||
# add a network rule to work-around Debian issues with two NICs on one network.
|
||||
mkdir -p "${destination}"/etc/udev/rules.d/
|
||||
cat <<- EOF > "${destination}"/etc/udev/rules.d/70-rename-lan.rules
|
||||
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="r8152", KERNEL=="eth*", NAME="lan0", \
|
||||
RUN+="/usr/sbin/ip link set lan0 down", \
|
||||
RUN+="/usr/sbin/ip link set eth0 down", \
|
||||
RUN+="/usr/bin/sleep 5s ", \
|
||||
RUN+="/usr/sbin/ip link set eth0 up", \
|
||||
RUN+="/usr/bin/sleep 10s ", \
|
||||
RUN+="/usr/sbin/ip link set lan0 up"
|
||||
EOF
|
||||
}
|
||||
|
||||
# Call the hook function above
|
||||
post_family_tweaks_bsp__enable_leds_orangepi_r1_plus_lts
|
||||
|
||||
|
||||
@@ -278,7 +278,7 @@ family_tweaks() {
|
||||
|
||||
chroot $SDCARD /bin/bash -c "systemctl --no-reload enable z28pro-bluetooth.service >/dev/null 2>&1"
|
||||
|
||||
elif [[ $BOARD == nanopi-r2s || $BOARD == nanopi-r2c || $BOARD == orangepi-r1plus || $BOARD == orangepi-r1plus-lts ]]; then
|
||||
elif [[ $BOARD == nanopi-r2s || $BOARD == nanopi-r2c || $BOARD == orangepi-r1plus ]]; then
|
||||
|
||||
# rename USB based network to lan0
|
||||
mkdir -p $SDCARD/etc/udev/rules.d/
|
||||
|
||||
@@ -1,19 +1,20 @@
|
||||
From: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Date: Sun, 10 Jul 2022 22:20:00 +1300
|
||||
Subject: rk3328-orangepi-r1-plus-lts.dts
|
||||
From c163dea909a2900a78ad8041de42b6509c8e3910 Mon Sep 17 00:00:00 2001
|
||||
From: schwar3kat <schwar3kat@armbian.com>
|
||||
Date: Mon, 30 Jan 2023 18:48:33 +1300
|
||||
Subject: [PATCH] add-board-orangepi-r1-plus-lts.patch
|
||||
|
||||
Signed-off-by: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Signed-off-by: schwar3kat <schwar3kat@armbian.com>
|
||||
---
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 444 ++++++++++++
|
||||
1 files changed, 444 insertions(+)
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 446 ++++++++++++++++++
|
||||
1 file changed, 446 insertions(+)
|
||||
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
|
||||
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
new file mode 100644
|
||||
index 000000000..10d50ebd4
|
||||
index 000000000..2bc432168
|
||||
--- /dev/null
|
||||
+++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
@@ -0,0 +1,444 @@
|
||||
@@ -0,0 +1,446 @@
|
||||
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
+/* Copyright (c) 2020 David Bauer <mail@david-bauer.net>
|
||||
+ * Copyright (c) 2020 Shenzhen Xunlong Software CO.,Limited
|
||||
@@ -63,18 +64,18 @@ index 000000000..10d50ebd4
|
||||
+
|
||||
+ leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ lan_led: led-0 {
|
||||
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ };
|
||||
+
|
||||
+ sys_led: led-1 {
|
||||
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:sys";
|
||||
+ default-state = "on";
|
||||
+ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:status";
|
||||
+ linux,default-trigger = "heartbeat";
|
||||
+ };
|
||||
+
|
||||
+ wan_led: led-2 {
|
||||
@@ -413,11 +414,13 @@ index 000000000..10d50ebd4
|
||||
+ status = "okay";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ snps,xhci-trb-ent-quirk;
|
||||
+
|
||||
+ /* Second port is for USB 3.0 */
|
||||
+ rtl8153: device@2 {
|
||||
+ compatible = "usbbda,8153";
|
||||
+ reg = <2>;
|
||||
+ realtek,led-data = <0x87>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
@@ -458,3 +461,6 @@ index 000000000..10d50ebd4
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+};
|
||||
--
|
||||
Created with Armbian build tools https://github.com/armbian/build
|
||||
|
||||
|
||||
@@ -0,0 +1,466 @@
|
||||
From c163dea909a2900a78ad8041de42b6509c8e3910 Mon Sep 17 00:00:00 2001
|
||||
From: schwar3kat <schwar3kat@armbian.com>
|
||||
Date: Mon, 30 Jan 2023 18:48:33 +1300
|
||||
Subject: [PATCH] add-board-orangepi-r1-plus-lts.patch
|
||||
|
||||
Signed-off-by: schwar3kat <schwar3kat@armbian.com>
|
||||
---
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 446 ++++++++++++++++++
|
||||
1 file changed, 446 insertions(+)
|
||||
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
|
||||
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
new file mode 100644
|
||||
index 000000000..2bc432168
|
||||
--- /dev/null
|
||||
+++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
@@ -0,0 +1,446 @@
|
||||
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
+/* Copyright (c) 2020 David Bauer <mail@david-bauer.net>
|
||||
+ * Copyright (c) 2020 Shenzhen Xunlong Software CO.,Limited
|
||||
+ * Copyright (c) 2021 AmadeusGhost <amadeus@jmu.edu.cn>
|
||||
+ * Revised for Orange Pi R1 Plus LTS (c) 2022 schwar3kat
|
||||
+ * Based on Orange Pi R1 plus
|
||||
+ */
|
||||
+
|
||||
+/dts-v1/;
|
||||
+
|
||||
+#include <dt-bindings/input/input.h>
|
||||
+#include <dt-bindings/gpio/gpio.h>
|
||||
+#include "rk3328.dtsi"
|
||||
+
|
||||
+/ {
|
||||
+ model = "Xunlong Orange Pi R1 Plus LTS";
|
||||
+ compatible = "xunlong,orangepi-r1-plus-lts", "rockchip,rk3328";
|
||||
+
|
||||
+ aliases {
|
||||
+ ethernet1 = &rtl8153;
|
||||
+ mmc0 = &sdmmc;
|
||||
+ };
|
||||
+
|
||||
+ chosen {
|
||||
+ stdout-path = "serial2:1500000n8";
|
||||
+ };
|
||||
+
|
||||
+ gmac_clk: gmac-clock {
|
||||
+ compatible = "fixed-clock";
|
||||
+ clock-frequency = <125000000>;
|
||||
+ clock-output-names = "gmac_clkin";
|
||||
+ #clock-cells = <0>;
|
||||
+ };
|
||||
+
|
||||
+ keys {
|
||||
+ compatible = "gpio-keys";
|
||||
+ pinctrl-0 = <&reset_button_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ reset {
|
||||
+ label = "reset";
|
||||
+ gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
|
||||
+ linux,code = <KEY_RESTART>;
|
||||
+ debounce-interval = <50>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ lan_led: led-0 {
|
||||
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ };
|
||||
+
|
||||
+ sys_led: led-1 {
|
||||
+ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:status";
|
||||
+ linux,default-trigger = "heartbeat";
|
||||
+ };
|
||||
+
|
||||
+ wan_led: led-2 {
|
||||
+ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:green:wan";
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ vcc_io_sdio: sdmmcio-regulator {
|
||||
+ compatible = "regulator-gpio";
|
||||
+ enable-active-high;
|
||||
+ gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>;
|
||||
+ pinctrl-0 = <&sdio_vcc_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+ regulator-name = "vcc_io_sdio";
|
||||
+ regulator-always-on;
|
||||
+ regulator-min-microvolt = <1800000>;
|
||||
+ regulator-max-microvolt = <3300000>;
|
||||
+ regulator-settling-time-us = <5000>;
|
||||
+ regulator-type = "voltage";
|
||||
+ startup-delay-us = <2000>;
|
||||
+ states = <1800000 0x1>,
|
||||
+ <3300000 0x0>;
|
||||
+ vin-supply = <&vcc_io_33>;
|
||||
+ };
|
||||
+
|
||||
+ vcc_sd: sdmmc-regulator {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
|
||||
+ pinctrl-0 = <&sdmmc0m1_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+ regulator-name = "vcc_sd";
|
||||
+ regulator-boot-on;
|
||||
+ regulator-min-microvolt = <3300000>;
|
||||
+ regulator-max-microvolt = <3300000>;
|
||||
+ vin-supply = <&vcc_io_33>;
|
||||
+ };
|
||||
+
|
||||
+ vdd_5v: vdd-5v {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ regulator-name = "vdd_5v";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ regulator-min-microvolt = <5000000>;
|
||||
+ regulator-max-microvolt = <5000000>;
|
||||
+ };
|
||||
+
|
||||
+ vdd_5v_lan: vdd-5v-lan {
|
||||
+ compatible = "regulator-fixed";
|
||||
+ enable-active-high;
|
||||
+ gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
|
||||
+ pinctrl-0 = <&lan_vdd_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+ regulator-name = "vdd_5v_lan";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ vin-supply = <&vdd_5v>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&cpu0 {
|
||||
+ cpu-supply = <&vdd_arm>;
|
||||
+};
|
||||
+
|
||||
+&cpu1 {
|
||||
+ cpu-supply = <&vdd_arm>;
|
||||
+};
|
||||
+
|
||||
+&cpu2 {
|
||||
+ cpu-supply = <&vdd_arm>;
|
||||
+};
|
||||
+
|
||||
+&cpu3 {
|
||||
+ cpu-supply = <&vdd_arm>;
|
||||
+};
|
||||
+
|
||||
+&display_subsystem {
|
||||
+ status = "disabled";
|
||||
+};
|
||||
+
|
||||
+&gmac2io {
|
||||
+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
|
||||
+ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
|
||||
+ clock_in_out = "input";
|
||||
+ phy-mode = "rgmii";
|
||||
+ phy-supply = <&vcc_io_33>;
|
||||
+ pinctrl-0 = <&rgmiim1_pins>;
|
||||
+ pinctrl-names = "default";
|
||||
+ snps,aal;
|
||||
+ status = "okay";
|
||||
+ phy-handle = <&yt8531c>;
|
||||
+ tx_delay = <0x19>;
|
||||
+ rx_delay = <0x05>;
|
||||
+
|
||||
+ mdio {
|
||||
+ compatible = "snps,dwmac-mdio";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+
|
||||
+ yt8531c: ethernet-phy@0 {
|
||||
+ compatible = "ethernet-phy-id4f51.e91b",
|
||||
+ "ethernet-phy-ieee802.3-c22";
|
||||
+ reg = <0>;
|
||||
+ pinctrl-0 = <ð_phy_reset_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+ reset-assert-us = <15000>;
|
||||
+ reset-deassert-us = <50000>;
|
||||
+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&i2c1 {
|
||||
+ status = "okay";
|
||||
+
|
||||
+ rk805: pmic@18 {
|
||||
+ compatible = "rockchip,rk805";
|
||||
+ reg = <0x18>;
|
||||
+ interrupt-parent = <&gpio1>;
|
||||
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
|
||||
+ #clock-cells = <1>;
|
||||
+ clock-output-names = "xin32k", "rk805-clkout2";
|
||||
+ gpio-controller;
|
||||
+ #gpio-cells = <2>;
|
||||
+ pinctrl-0 = <&pmic_int_l>;
|
||||
+ pinctrl-names = "default";
|
||||
+ rockchip,system-power-controller;
|
||||
+ wakeup-source;
|
||||
+
|
||||
+ vcc1-supply = <&vdd_5v>;
|
||||
+ vcc2-supply = <&vdd_5v>;
|
||||
+ vcc3-supply = <&vdd_5v>;
|
||||
+ vcc4-supply = <&vdd_5v>;
|
||||
+ vcc5-supply = <&vcc_io_33>;
|
||||
+ vcc6-supply = <&vdd_5v>;
|
||||
+
|
||||
+ regulators {
|
||||
+ vdd_log: DCDC_REG1 {
|
||||
+ regulator-name = "vdd_log";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ regulator-min-microvolt = <712500>;
|
||||
+ regulator-max-microvolt = <1450000>;
|
||||
+ regulator-ramp-delay = <12500>;
|
||||
+
|
||||
+ regulator-state-mem {
|
||||
+ regulator-on-in-suspend;
|
||||
+ regulator-suspend-microvolt = <1000000>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ vdd_arm: DCDC_REG2 {
|
||||
+ regulator-name = "vdd_arm";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ regulator-min-microvolt = <712500>;
|
||||
+ regulator-max-microvolt = <1450000>;
|
||||
+ regulator-ramp-delay = <12500>;
|
||||
+
|
||||
+ regulator-state-mem {
|
||||
+ regulator-on-in-suspend;
|
||||
+ regulator-suspend-microvolt = <950000>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ vcc_ddr: DCDC_REG3 {
|
||||
+ regulator-name = "vcc_ddr";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+
|
||||
+ regulator-state-mem {
|
||||
+ regulator-on-in-suspend;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ vcc_io_33: DCDC_REG4 {
|
||||
+ regulator-name = "vcc_io_33";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ regulator-min-microvolt = <3300000>;
|
||||
+ regulator-max-microvolt = <3300000>;
|
||||
+
|
||||
+ regulator-state-mem {
|
||||
+ regulator-on-in-suspend;
|
||||
+ regulator-suspend-microvolt = <3300000>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ vcc_18: LDO_REG1 {
|
||||
+ regulator-name = "vcc_18";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ regulator-min-microvolt = <1800000>;
|
||||
+ regulator-max-microvolt = <1800000>;
|
||||
+
|
||||
+ regulator-state-mem {
|
||||
+ regulator-on-in-suspend;
|
||||
+ regulator-suspend-microvolt = <1800000>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ vcc18_emmc: LDO_REG2 {
|
||||
+ regulator-name = "vcc18_emmc";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ regulator-min-microvolt = <1800000>;
|
||||
+ regulator-max-microvolt = <1800000>;
|
||||
+
|
||||
+ regulator-state-mem {
|
||||
+ regulator-on-in-suspend;
|
||||
+ regulator-suspend-microvolt = <1800000>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ vdd_10: LDO_REG3 {
|
||||
+ regulator-name = "vdd_10";
|
||||
+ regulator-always-on;
|
||||
+ regulator-boot-on;
|
||||
+ regulator-min-microvolt = <1000000>;
|
||||
+ regulator-max-microvolt = <1000000>;
|
||||
+
|
||||
+ regulator-state-mem {
|
||||
+ regulator-on-in-suspend;
|
||||
+ regulator-suspend-microvolt = <1000000>;
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&io_domains {
|
||||
+ pmuio-supply = <&vcc_io_33>;
|
||||
+ vccio1-supply = <&vcc_io_33>;
|
||||
+ vccio2-supply = <&vcc18_emmc>;
|
||||
+ vccio3-supply = <&vcc_io_sdio>;
|
||||
+ vccio4-supply = <&vcc_18>;
|
||||
+ vccio5-supply = <&vcc_io_33>;
|
||||
+ vccio6-supply = <&vcc_io_33>;
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&pinctrl {
|
||||
+ button {
|
||||
+ reset_button_pin: reset-button-pin {
|
||||
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ gmac2io {
|
||||
+ eth_phy_reset_pin: eth-phy-reset-pin {
|
||||
+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ leds {
|
||||
+ lan_led_pin: lan-led-pin {
|
||||
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
+ };
|
||||
+
|
||||
+ sys_led_pin: sys-led-pin {
|
||||
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
+ };
|
||||
+
|
||||
+ wan_led_pin: wan-led-pin {
|
||||
+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ lan {
|
||||
+ lan_vdd_pin: lan-vdd-pin {
|
||||
+ rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ pmic {
|
||||
+ pmic_int_l: pmic-int-l {
|
||||
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
+ };
|
||||
+ };
|
||||
+
|
||||
+ sd {
|
||||
+ sdio_vcc_pin: sdio-vcc-pin {
|
||||
+ rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
+ };
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&pwm2 {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&sdmmc {
|
||||
+ bus-width = <4>;
|
||||
+ cap-sd-highspeed;
|
||||
+ disable-wp;
|
||||
+ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
|
||||
+ pinctrl-names = "default";
|
||||
+ sd-uhs-sdr12;
|
||||
+ sd-uhs-sdr25;
|
||||
+ sd-uhs-sdr50;
|
||||
+ sd-uhs-sdr104;
|
||||
+ vmmc-supply = <&vcc_sd>;
|
||||
+ vqmmc-supply = <&vcc_io_sdio>;
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&tsadc {
|
||||
+ rockchip,hw-tshut-mode = <0>;
|
||||
+ rockchip,hw-tshut-polarity = <0>;
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&u2phy {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&u2phy_host {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&u2phy_otg {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&uart2 {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&usb20_otg {
|
||||
+ status = "okay";
|
||||
+ dr_mode = "host";
|
||||
+};
|
||||
+
|
||||
+&usbdrd3 {
|
||||
+ dr_mode = "host";
|
||||
+ status = "okay";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ snps,xhci-trb-ent-quirk;
|
||||
+
|
||||
+ /* Second port is for USB 3.0 */
|
||||
+ rtl8153: device@2 {
|
||||
+ compatible = "usbbda,8153";
|
||||
+ reg = <2>;
|
||||
+ realtek,led-data = <0x87>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&usb_host0_ehci {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&usb_host0_ohci {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&spi0 {
|
||||
+ max-freq = <48000000>;
|
||||
+ status = "okay";
|
||||
+
|
||||
+ flash@0 {
|
||||
+ compatible = "jedec,spi-nor";
|
||||
+ reg = <0>;
|
||||
+ spi-max-frequency = <10000000>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
+&uart1 {
|
||||
+ status = "okay";
|
||||
+};
|
||||
+
|
||||
+&dmc_opp_table {
|
||||
+ opp-798000000 {
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+ opp-840000000 {
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+ opp-924000000 {
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+ opp-1056000000 {
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+};
|
||||
--
|
||||
Created with Armbian build tools https://github.com/armbian/build
|
||||
|
||||
@@ -1,19 +1,20 @@
|
||||
From: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Date: Sun, 10 Jul 2022 22:20:00 +1300
|
||||
Subject: rk3328-orangepi-r1-plus-lts.dts
|
||||
From c163dea909a2900a78ad8041de42b6509c8e3910 Mon Sep 17 00:00:00 2001
|
||||
From: schwar3kat <schwar3kat@armbian.com>
|
||||
Date: Mon, 30 Jan 2023 18:48:33 +1300
|
||||
Subject: [PATCH] add-board-orangepi-r1-plus-lts.patch
|
||||
|
||||
Signed-off-by: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Signed-off-by: schwar3kat <schwar3kat@armbian.com>
|
||||
---
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 444 ++++++++++++
|
||||
1 files changed, 444 insertions(+)
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 446 ++++++++++++++++++
|
||||
1 file changed, 446 insertions(+)
|
||||
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
|
||||
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
new file mode 100644
|
||||
index 000000000..10d50ebd4
|
||||
index 000000000..2bc432168
|
||||
--- /dev/null
|
||||
+++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
@@ -0,0 +1,444 @@
|
||||
@@ -0,0 +1,446 @@
|
||||
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
+/* Copyright (c) 2020 David Bauer <mail@david-bauer.net>
|
||||
+ * Copyright (c) 2020 Shenzhen Xunlong Software CO.,Limited
|
||||
@@ -63,18 +64,18 @@ index 000000000..10d50ebd4
|
||||
+
|
||||
+ leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ lan_led: led-0 {
|
||||
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ };
|
||||
+
|
||||
+ sys_led: led-1 {
|
||||
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:sys";
|
||||
+ default-state = "on";
|
||||
+ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:status";
|
||||
+ linux,default-trigger = "heartbeat";
|
||||
+ };
|
||||
+
|
||||
+ wan_led: led-2 {
|
||||
@@ -413,11 +414,13 @@ index 000000000..10d50ebd4
|
||||
+ status = "okay";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ snps,xhci-trb-ent-quirk;
|
||||
+
|
||||
+ /* Second port is for USB 3.0 */
|
||||
+ rtl8153: device@2 {
|
||||
+ compatible = "usbbda,8153";
|
||||
+ reg = <2>;
|
||||
+ realtek,led-data = <0x87>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
@@ -458,3 +461,6 @@ index 000000000..10d50ebd4
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+};
|
||||
--
|
||||
Created with Armbian build tools https://github.com/armbian/build
|
||||
|
||||
|
||||
@@ -1,19 +1,20 @@
|
||||
From: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Date: Sun, 10 Jul 2022 22:20:00 +1300
|
||||
Subject: rk3328-orangepi-r1-plus-lts.dts
|
||||
From c163dea909a2900a78ad8041de42b6509c8e3910 Mon Sep 17 00:00:00 2001
|
||||
From: schwar3kat <schwar3kat@armbian.com>
|
||||
Date: Mon, 30 Jan 2023 18:48:33 +1300
|
||||
Subject: [PATCH] add-board-orangepi-r1-plus-lts.patch
|
||||
|
||||
Signed-off-by: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Signed-off-by: schwar3kat <schwar3kat@armbian.com>
|
||||
---
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 444 ++++++++++++
|
||||
1 files changed, 444 insertions(+)
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 446 ++++++++++++++++++
|
||||
1 file changed, 446 insertions(+)
|
||||
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
|
||||
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
new file mode 100644
|
||||
index 000000000..10d50ebd4
|
||||
index 000000000..2bc432168
|
||||
--- /dev/null
|
||||
+++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
@@ -0,0 +1,444 @@
|
||||
@@ -0,0 +1,446 @@
|
||||
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
+/* Copyright (c) 2020 David Bauer <mail@david-bauer.net>
|
||||
+ * Copyright (c) 2020 Shenzhen Xunlong Software CO.,Limited
|
||||
@@ -63,18 +64,18 @@ index 000000000..10d50ebd4
|
||||
+
|
||||
+ leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ lan_led: led-0 {
|
||||
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ };
|
||||
+
|
||||
+ sys_led: led-1 {
|
||||
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:sys";
|
||||
+ default-state = "on";
|
||||
+ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:status";
|
||||
+ linux,default-trigger = "heartbeat";
|
||||
+ };
|
||||
+
|
||||
+ wan_led: led-2 {
|
||||
@@ -413,11 +414,13 @@ index 000000000..10d50ebd4
|
||||
+ status = "okay";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ snps,xhci-trb-ent-quirk;
|
||||
+
|
||||
+ /* Second port is for USB 3.0 */
|
||||
+ rtl8153: device@2 {
|
||||
+ compatible = "usbbda,8153";
|
||||
+ reg = <2>;
|
||||
+ realtek,led-data = <0x87>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
@@ -458,3 +461,6 @@ index 000000000..10d50ebd4
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+};
|
||||
--
|
||||
Created with Armbian build tools https://github.com/armbian/build
|
||||
|
||||
|
||||
@@ -1,19 +1,20 @@
|
||||
From: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Date: Sun, 10 Jul 2022 22:20:00 +1300
|
||||
Subject: rk3328-orangepi-r1-plus-lts.dts
|
||||
From c163dea909a2900a78ad8041de42b6509c8e3910 Mon Sep 17 00:00:00 2001
|
||||
From: schwar3kat <schwar3kat@armbian.com>
|
||||
Date: Mon, 30 Jan 2023 18:48:33 +1300
|
||||
Subject: [PATCH] add-board-orangepi-r1-plus-lts.patch
|
||||
|
||||
Signed-off-by: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Signed-off-by: schwar3kat <schwar3kat@armbian.com>
|
||||
---
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 444 ++++++++++++
|
||||
1 files changed, 444 insertions(+)
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 446 ++++++++++++++++++
|
||||
1 file changed, 446 insertions(+)
|
||||
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
|
||||
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
new file mode 100644
|
||||
index 000000000..10d50ebd4
|
||||
index 000000000..2bc432168
|
||||
--- /dev/null
|
||||
+++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
@@ -0,0 +1,444 @@
|
||||
@@ -0,0 +1,446 @@
|
||||
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
+/* Copyright (c) 2020 David Bauer <mail@david-bauer.net>
|
||||
+ * Copyright (c) 2020 Shenzhen Xunlong Software CO.,Limited
|
||||
@@ -63,18 +64,18 @@ index 000000000..10d50ebd4
|
||||
+
|
||||
+ leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ lan_led: led-0 {
|
||||
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ };
|
||||
+
|
||||
+ sys_led: led-1 {
|
||||
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:sys";
|
||||
+ default-state = "on";
|
||||
+ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:status";
|
||||
+ linux,default-trigger = "heartbeat";
|
||||
+ };
|
||||
+
|
||||
+ wan_led: led-2 {
|
||||
@@ -413,11 +414,13 @@ index 000000000..10d50ebd4
|
||||
+ status = "okay";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ snps,xhci-trb-ent-quirk;
|
||||
+
|
||||
+ /* Second port is for USB 3.0 */
|
||||
+ rtl8153: device@2 {
|
||||
+ compatible = "usbbda,8153";
|
||||
+ reg = <2>;
|
||||
+ realtek,led-data = <0x87>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
@@ -458,3 +461,6 @@ index 000000000..10d50ebd4
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+};
|
||||
--
|
||||
Created with Armbian build tools https://github.com/armbian/build
|
||||
|
||||
|
||||
@@ -1,19 +1,20 @@
|
||||
From: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Date: Sun, 10 Jul 2022 22:20:00 +1300
|
||||
Subject: rk3328-orangepi-r1-plus-lts.dts
|
||||
From c163dea909a2900a78ad8041de42b6509c8e3910 Mon Sep 17 00:00:00 2001
|
||||
From: schwar3kat <schwar3kat@armbian.com>
|
||||
Date: Mon, 30 Jan 2023 18:48:33 +1300
|
||||
Subject: [PATCH] add-board-orangepi-r1-plus-lts.patch
|
||||
|
||||
Signed-off-by: schwar3kat <61094841+schwar3kat@users.noreply.github.com>
|
||||
Signed-off-by: schwar3kat <schwar3kat@armbian.com>
|
||||
---
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 444 ++++++++++++
|
||||
1 files changed, 444 insertions(+)
|
||||
.../rockchip/rk3328-orangepi-r1-plus-lts.dts | 446 ++++++++++++++++++
|
||||
1 file changed, 446 insertions(+)
|
||||
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
|
||||
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
new file mode 100644
|
||||
index 000000000..10d50ebd4
|
||||
index 000000000..2bc432168
|
||||
--- /dev/null
|
||||
+++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
|
||||
@@ -0,0 +1,444 @@
|
||||
@@ -0,0 +1,446 @@
|
||||
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
+/* Copyright (c) 2020 David Bauer <mail@david-bauer.net>
|
||||
+ * Copyright (c) 2020 Shenzhen Xunlong Software CO.,Limited
|
||||
@@ -63,18 +64,18 @@ index 000000000..10d50ebd4
|
||||
+
|
||||
+ leds {
|
||||
+ compatible = "gpio-leds";
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
|
||||
+ pinctrl-names = "default";
|
||||
+
|
||||
+ lan_led: led-0 {
|
||||
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ label = "orangepi-r1-plus-lts:green:lan";
|
||||
+ };
|
||||
+
|
||||
+ sys_led: led-1 {
|
||||
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:sys";
|
||||
+ default-state = "on";
|
||||
+ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
+ label = "orangepi-r1-plus-lts:red:status";
|
||||
+ linux,default-trigger = "heartbeat";
|
||||
+ };
|
||||
+
|
||||
+ wan_led: led-2 {
|
||||
@@ -413,11 +414,13 @@ index 000000000..10d50ebd4
|
||||
+ status = "okay";
|
||||
+ #address-cells = <1>;
|
||||
+ #size-cells = <0>;
|
||||
+ snps,xhci-trb-ent-quirk;
|
||||
+
|
||||
+ /* Second port is for USB 3.0 */
|
||||
+ rtl8153: device@2 {
|
||||
+ compatible = "usbbda,8153";
|
||||
+ reg = <2>;
|
||||
+ realtek,led-data = <0x87>;
|
||||
+ };
|
||||
+};
|
||||
+
|
||||
@@ -458,3 +461,6 @@ index 000000000..10d50ebd4
|
||||
+ status = "disabled";
|
||||
+ };
|
||||
+};
|
||||
--
|
||||
Created with Armbian build tools https://github.com/armbian/build
|
||||
|
||||
|
||||
Reference in New Issue
Block a user