Removed WIP status
Added CONFIG_R8169=m to defconfig(s) (eth support)
Modified and added additional patches (linux 6.1 / 6.4)
U-Boot v2023.07.2 (dropped v2022.10)
Upstream BT FW (rtl8822cs) is now shared between CM4IO and M2s
Signed-off-by: Patrick Yavitz <pyavitz@xxxxx.com>
BPI-CM4:
In accordance with the BSP DTS, set LED gpio to GPIO_ACTIVE_LOW.
Added default-on trigger to led-green
Board now powers off, added reboot node 'meson64-reboot'.
CONFIG_POWER_RESET_MESON64
Isolated RESET ODROID driver and renamed to MESON64 as it can be used in more than ODROIDS.
MESON UART
Series improves support for UART attached Bluetooth modules on Amlogic Meson G12A and newer SoCs. These SoCs also support the "divide XTAL by 2" bit which (greatly) reduces jitter when generating baud rates such as 1500000 (which is used by the Bluetooth part of the RTL8822CS SDIO WiFi and UART Bluetooth combo chip).
Signed-off-by: Patrick Yavitz <pyavitz@gmail.com>
* Remove deprecated Odroid XU4 legacy 4.14.y branch
* Clean deprecated kernels from meson64 family
- legacy kernel 4.9 was removed
- current 5.10 was replaced with 5.19
- edge remains on 5.19 until someone bumps it to 6
- patches between 5.11 and 5.18 were removed, 5.10 will be kept for awhile
* Update configs
* rk35xx: enable the CONFIG_F2FS_FS_COMPRESSION option
This allows to use compression on a F2FS partition to save space and
reduce I/O operations to media.
* all: enable the CONFIG_F2FS_FS_COMPRESSION option
- starting from Home Assistant OS (HASSOS) setup/patchset, which is stable with pure-mainline
- *huge thanks* to Stefan Agner (@agners) from Home Assistant for his work and help with this
- CONFIG_DRM_MESON=y fixes the order of shutdown callbacks, allowing it to reboot without patches
- this increases the kernel size a bit, due to some dependencies like DRM=y
- remove the shutdown revert patch, allowing other meson64 boards to mainline-reboot
- add fdt/no-map patch fixing the dreaded "SError Interrupt on CPU4" panics that plagued the N2
- move the N2 to mainline u-boot on current (rebased, already done)
- add SPI-enabling DTB variants, which allow writing to SPI NOR flash (and usage instructions in comments)
- add UBOOT_TARGET_MAP and write_uboot_platform_mtd to current, for nand-sata-install to SPI/USB goodness
- remove the UHS-enabling patch, to avoid 1.8v vs 3.3v mess. Make sure to use only A1-rated SD cards as recommended.
- change default cpufreq governor for 24h+ stability
- other patch cleanups:
- move deprecated/non-applying patch to need-check
- remove the HardKernel ODROID-specific reboot driver and DTS patches (odroid-reboot.c) which are now useless.
- remove documentation-only patches (we have enough patches in meson64 without those)
- remove duplicated SAR ADC patches
- remove multiple different and conflicting patches for DTS and emulated-PWM GPIO fan
- now using simple on/off GPIO fan at 30 celsius, unrelated to passive cooling
* [rockchip64-current] add gamepad and joystick support
Added modules similar to rockchip64-legacy
* [meson{64}-current] add gamepad and joystick support
* [gitignore] temp vim files
* [sunxi{64}-current] add gamepad and joystick support
* [mvebu{64}-current] add gamepad and joystick support
* [misc dev] add gamepad and joystick support
* [meson and sunxi legacy] add gamepad and joystick support
* [misc legacy] add gamepad and joystick support
* Enable TARGET_CORE module to run & publish iSCSI targets on armbian.
* Enable all iSCSI modules (IBLOCK,FILEIO,PSCSI) on all platforms.
* Revert "Enable all iSCSI modules (IBLOCK,FILEIO,PSCSI) on all platforms."
This reverts commit 7ab3882e0c.
* Enable all iSCSI modules (IBLOCK,FILEIO,PSCSI) on all platforms.
Co-authored-by: Luis Garcia <luis@Disgaea.local>
