mirror of
https://github.com/armbian/build
synced 2025-09-24 19:47:06 +07:00
mixtile-edge2: add rk3568 board (current/edge/vendor)
- in main `rockchip64` family, for current/edge (6.6 / 6.11) - using mainline u-boot's generic rk3568 for current/edge - vendor kernel is added via a copypasta hook to piggyback on `rk35xx` - requires armbian/linux-rockchip PR https://github.com/armbian/linux-rockchip/pull/245 - vendor u-boot: - is required to bringup npu for vendor kernel (otherwise panics) - .dts done based on vendor kernel DT + looking at armsom-sige3 - defconfig ripped off from armsom-sige3
This commit is contained in:
Ricardo Pardini
@@ -0,0 +1,237 @@
|
||||
CONFIG_ARM=y
|
||||
CONFIG_ARCH_ROCKCHIP=y
|
||||
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
||||
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
||||
CONFIG_SYS_MALLOC_F_LEN=0x80000
|
||||
CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-rockchip/make_fit_atf.sh"
|
||||
CONFIG_ROCKCHIP_RK3568=y
|
||||
CONFIG_ROCKCHIP_FIT_IMAGE=y
|
||||
CONFIG_ROCKCHIP_VENDOR_PARTITION=y
|
||||
CONFIG_ROCKCHIP_FIT_IMAGE_PACK=y
|
||||
CONFIG_ROCKCHIP_NEW_IDB=y
|
||||
CONFIG_SPL_SERIAL_SUPPORT=y
|
||||
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
|
||||
CONFIG_TARGET_EVB_RK3568=y
|
||||
CONFIG_SPL_LIBDISK_SUPPORT=y
|
||||
CONFIG_SPL_NAND_SUPPORT=y
|
||||
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
||||
CONFIG_SPL_SPI_SUPPORT=y
|
||||
CONFIG_DEFAULT_DEVICE_TREE="rk3568-mixtile-edge2"
|
||||
CONFIG_DEBUG_UART=y
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_IMAGE_POST_PROCESS=y
|
||||
CONFIG_FIT_HW_CRYPTO=y
|
||||
CONFIG_SPL_LOAD_FIT=y
|
||||
CONFIG_SPL_FIT_IMAGE_POST_PROCESS=y
|
||||
CONFIG_SPL_FIT_HW_CRYPTO=y
|
||||
# CONFIG_SPL_SYS_DCACHE_OFF is not set
|
||||
CONFIG_BOOTDELAY=0
|
||||
CONFIG_SYS_CONSOLE_INFO_QUIET=y
|
||||
# CONFIG_DISPLAY_CPUINFO is not set
|
||||
CONFIG_ANDROID_BOOTLOADER=y
|
||||
CONFIG_ANDROID_AVB=y
|
||||
CONFIG_ANDROID_BOOT_IMAGE_HASH=y
|
||||
CONFIG_SPL_BOARD_INIT=y
|
||||
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
|
||||
# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set
|
||||
CONFIG_SPL_SEPARATE_BSS=y
|
||||
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
|
||||
CONFIG_SPL_SHA256_SUPPORT=y
|
||||
CONFIG_SPL_CRYPTO_SUPPORT=y
|
||||
CONFIG_SPL_HASH_SUPPORT=y
|
||||
CONFIG_SPL_MTD_SUPPORT=y
|
||||
CONFIG_SPL_ATF=y
|
||||
CONFIG_SPL_ATF_NO_PLATFORM_PARAM=y
|
||||
CONFIG_SPL_AB=y
|
||||
CONFIG_FASTBOOT_BUF_ADDR=0xc00800
|
||||
CONFIG_FASTBOOT_BUF_SIZE=0x04000000
|
||||
CONFIG_FASTBOOT_FLASH=y
|
||||
CONFIG_FASTBOOT_FLASH_MMC_DEV=0
|
||||
CONFIG_CMD_BOOTZ=y
|
||||
CONFIG_CMD_DTIMG=y
|
||||
# CONFIG_CMD_ELF is not set
|
||||
# CONFIG_CMD_IMI is not set
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
# CONFIG_CMD_XIMG is not set
|
||||
# CONFIG_CMD_LZMADEC is not set
|
||||
# CONFIG_CMD_UNZIP is not set
|
||||
# CONFIG_CMD_FLASH is not set
|
||||
# CONFIG_CMD_FPGA is not set
|
||||
CONFIG_CMD_GPT=y
|
||||
# CONFIG_CMD_LOADB is not set
|
||||
# CONFIG_CMD_LOADS is not set
|
||||
CONFIG_CMD_BOOT_ANDROID=y
|
||||
CONFIG_CMD_BOOT_ROCKCHIP=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_MTD=y
|
||||
CONFIG_CMD_NAND=y
|
||||
CONFIG_CMD_PCI=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_USB_MASS_STORAGE=y
|
||||
# CONFIG_CMD_ITEST is not set
|
||||
# CONFIG_CMD_SETEXPR is not set
|
||||
CONFIG_CMD_TFTPPUT=y
|
||||
CONFIG_CMD_TFTP_BOOTM=y
|
||||
CONFIG_CMD_TFTP_FLASH=y
|
||||
# CONFIG_CMD_MISC is not set
|
||||
CONFIG_CMD_MTD_BLK=y
|
||||
# CONFIG_SPL_DOS_PARTITION is not set
|
||||
# CONFIG_ISO_PARTITION is not set
|
||||
CONFIG_EFI_PARTITION_ENTRIES_NUMBERS=64
|
||||
CONFIG_SPL_OF_CONTROL=y
|
||||
CONFIG_SPL_DTB_MINIMUM=y
|
||||
CONFIG_OF_LIVE=y
|
||||
CONFIG_OF_SPL_REMOVE_PROPS=""
|
||||
# CONFIG_NET_TFTP_VARS is not set
|
||||
CONFIG_REGMAP=y
|
||||
CONFIG_SPL_REGMAP=y
|
||||
CONFIG_SYSCON=y
|
||||
CONFIG_SPL_SYSCON=y
|
||||
CONFIG_CLK=y
|
||||
CONFIG_SPL_CLK=y
|
||||
CONFIG_CLK_SCMI=y
|
||||
CONFIG_DM_CRYPTO=y
|
||||
CONFIG_SPL_DM_CRYPTO=y
|
||||
CONFIG_ROCKCHIP_CRYPTO_V2=y
|
||||
CONFIG_SPL_ROCKCHIP_CRYPTO_V2=y
|
||||
CONFIG_DM_RNG=y
|
||||
CONFIG_RNG_ROCKCHIP=y
|
||||
CONFIG_SCMI_FIRMWARE=y
|
||||
CONFIG_ROCKCHIP_GPIO=y
|
||||
CONFIG_ROCKCHIP_GPIO_V2=y
|
||||
CONFIG_SYS_I2C_ROCKCHIP=y
|
||||
CONFIG_I2C_MUX=y
|
||||
CONFIG_DM_KEY=y
|
||||
CONFIG_RK8XX_PWRKEY=y
|
||||
CONFIG_ADC_KEY=y
|
||||
CONFIG_MISC=y
|
||||
CONFIG_SPL_MISC=y
|
||||
CONFIG_ROCKCHIP_OTP=y
|
||||
CONFIG_SPL_ROCKCHIP_SECURE_OTP=y
|
||||
CONFIG_MMC_DW=y
|
||||
CONFIG_MMC_DW_ROCKCHIP=y
|
||||
CONFIG_MMC_SDHCI=y
|
||||
CONFIG_MMC_SDHCI_SDMA=y
|
||||
CONFIG_MMC_SDHCI_ROCKCHIP=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_BLK=y
|
||||
CONFIG_MTD_DEVICE=y
|
||||
CONFIG_NAND=y
|
||||
CONFIG_NAND_ROCKCHIP_V9=y
|
||||
CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
|
||||
CONFIG_SYS_NAND_U_BOOT_OFFS=0x8000
|
||||
CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND=0x10000
|
||||
CONFIG_MTD_SPI_NAND=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SF_DEFAULT_SPEED=20000000
|
||||
CONFIG_SPI_FLASH_EON=y
|
||||
CONFIG_SPI_FLASH_GIGADEVICE=y
|
||||
CONFIG_SPI_FLASH_MACRONIX=y
|
||||
CONFIG_SPI_FLASH_WINBOND=y
|
||||
CONFIG_SPI_FLASH_XMC=y
|
||||
CONFIG_SPI_FLASH_MTD=y
|
||||
CONFIG_DM_ETH=y
|
||||
CONFIG_DM_ETH_PHY=y
|
||||
CONFIG_DWC_ETH_QOS=y
|
||||
CONFIG_GMAC_ROCKCHIP=y
|
||||
CONFIG_NVME=y
|
||||
CONFIG_PCI=y
|
||||
CONFIG_DM_PCI=y
|
||||
CONFIG_DM_PCI_COMPAT=y
|
||||
CONFIG_PCIE_DW_ROCKCHIP=y
|
||||
CONFIG_PHY_ROCKCHIP_INNO_USB2=y
|
||||
CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
|
||||
CONFIG_PHY_ROCKCHIP_NANENG_EDP=y
|
||||
CONFIG_PHY_ROCKCHIP_SNPS_PCIE3=y
|
||||
CONFIG_PINCTRL=y
|
||||
CONFIG_SPL_PINCTRL=y
|
||||
CONFIG_DM_FUEL_GAUGE=y
|
||||
CONFIG_POWER_FG_RK817=y
|
||||
CONFIG_IO_DOMAIN=y
|
||||
CONFIG_ROCKCHIP_IO_DOMAIN=y
|
||||
CONFIG_DM_PMIC=y
|
||||
CONFIG_PMIC_RK8XX=y
|
||||
CONFIG_DM_POWER_DELIVERY=y
|
||||
CONFIG_TYPEC_TCPM=y
|
||||
CONFIG_TYPEC_TCPCI=y
|
||||
CONFIG_TYPEC_HUSB311=y
|
||||
CONFIG_TYPEC_FUSB302=y
|
||||
CONFIG_REGULATOR_PWM=y
|
||||
CONFIG_DM_REGULATOR_FIXED=y
|
||||
CONFIG_DM_REGULATOR_GPIO=y
|
||||
CONFIG_REGULATOR_RK860X=y
|
||||
CONFIG_REGULATOR_RK8XX=y
|
||||
CONFIG_DM_CHARGE_DISPLAY=y
|
||||
CONFIG_CHARGE_ANIMATION=y
|
||||
CONFIG_PWM_ROCKCHIP=y
|
||||
CONFIG_RAM=y
|
||||
CONFIG_SPL_RAM=y
|
||||
CONFIG_TPL_RAM=y
|
||||
CONFIG_DM_RAMDISK=y
|
||||
CONFIG_RAMDISK_RO=y
|
||||
CONFIG_DM_DMC=y
|
||||
CONFIG_ROCKCHIP_DMC_FSP=y
|
||||
CONFIG_ROCKCHIP_SDRAM_COMMON=y
|
||||
CONFIG_ROCKCHIP_TPL_INIT_DRAM_TYPE=0
|
||||
CONFIG_DM_RESET=y
|
||||
CONFIG_SPL_DM_RESET=y
|
||||
CONFIG_SPL_RESET_ROCKCHIP=y
|
||||
CONFIG_BAUDRATE=1500000
|
||||
CONFIG_DEBUG_UART_BASE=0xFE660000
|
||||
CONFIG_DEBUG_UART_CLOCK=24000000
|
||||
CONFIG_DEBUG_UART_SHIFT=2
|
||||
CONFIG_ROCKCHIP_SFC=y
|
||||
CONFIG_SYSRESET=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_XHCI_HCD=y
|
||||
CONFIG_USB_XHCI_DWC3=y
|
||||
CONFIG_USB_EHCI_HCD=y
|
||||
CONFIG_USB_EHCI_GENERIC=y
|
||||
CONFIG_USB_OHCI_HCD=y
|
||||
CONFIG_USB_OHCI_GENERIC=y
|
||||
CONFIG_USB_DWC3=y
|
||||
CONFIG_USB_DWC3_GADGET=y
|
||||
CONFIG_USB_DWC3_GENERIC=y
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_USB_GADGET=y
|
||||
CONFIG_USB_GADGET_MANUFACTURER="Rockchip"
|
||||
CONFIG_USB_GADGET_VENDOR_NUM=0x2207
|
||||
CONFIG_USB_GADGET_PRODUCT_NUM=0x350a
|
||||
CONFIG_USB_GADGET_DOWNLOAD=y
|
||||
CONFIG_DM_VIDEO=y
|
||||
CONFIG_DISPLAY=y
|
||||
CONFIG_DRM_ROCKCHIP=y
|
||||
CONFIG_DRM_ROCKCHIP_DW_HDMI=y
|
||||
CONFIG_DRM_ROCKCHIP_INNO_MIPI_PHY=y
|
||||
CONFIG_DRM_ROCKCHIP_INNO_VIDEO_COMBO_PHY=y
|
||||
CONFIG_DRM_ROCKCHIP_DW_MIPI_DSI=y
|
||||
CONFIG_DRM_ROCKCHIP_ANALOGIX_DP=y
|
||||
CONFIG_DRM_ROCKCHIP_LVDS=y
|
||||
CONFIG_DRM_ROCKCHIP_RGB=y
|
||||
CONFIG_ROCKCHIP_CUBIC_LUT_SIZE=9
|
||||
CONFIG_LCD=y
|
||||
CONFIG_USE_TINY_PRINTF=y
|
||||
CONFIG_SPL_TINY_MEMSET=y
|
||||
CONFIG_RSA=y
|
||||
CONFIG_SPL_RSA=y
|
||||
CONFIG_RSA_N_SIZE=0x200
|
||||
CONFIG_RSA_E_SIZE=0x10
|
||||
CONFIG_RSA_C_SIZE=0x20
|
||||
CONFIG_XBC=y
|
||||
CONFIG_SHA512=y
|
||||
CONFIG_LZ4=y
|
||||
CONFIG_LZMA=y
|
||||
CONFIG_SPL_GZIP=y
|
||||
CONFIG_ERRNO_STR=y
|
||||
# CONFIG_EFI_LOADER is not set
|
||||
CONFIG_AVB_LIBAVB=y
|
||||
CONFIG_AVB_LIBAVB_AB=y
|
||||
CONFIG_AVB_LIBAVB_ATX=y
|
||||
CONFIG_AVB_LIBAVB_USER=y
|
||||
CONFIG_RK_AVB_LIBAVB_USER=y
|
||||
CONFIG_OPTEE_CLIENT=y
|
||||
CONFIG_OPTEE_V2=y
|
||||
CONFIG_CMD_CHARGE_DISPLAY=y
|
||||
CONFIG_DM_CHARGE_DISPLAY=y
|
||||
CONFIG_CMD_PMIC=y
|
||||
CONFIG_CMD_REGULATOR=y
|
||||
@@ -0,0 +1,655 @@
|
||||
/*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*
|
||||
* (C) Copyright 2020 Rockchip Electronics Co., Ltd
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
#include "rk3568.dtsi"
|
||||
#include "rk3568-u-boot.dtsi"
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/usb/pd.h>
|
||||
|
||||
/ {
|
||||
|
||||
model = "Mixtile Edge 2";
|
||||
compatible = "focalcrest,mixtile-edge2", "rockchip,rk3568";
|
||||
|
||||
leds: leds {
|
||||
compatible = "gpio-leds";
|
||||
work_led: work {
|
||||
gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
keys: gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
button@0 {
|
||||
gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
|
||||
label = "GPIO Loader";
|
||||
linux,code = <KEY_VOLUMEUP>;
|
||||
};
|
||||
};
|
||||
|
||||
dc_12v: dc-12v {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "dc_12v";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <12000000>;
|
||||
regulator-max-microvolt = <12000000>;
|
||||
};
|
||||
|
||||
vcc2v5_sys: vcc2v5-ddr {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc2v5-sys";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <2500000>;
|
||||
regulator-max-microvolt = <2500000>;
|
||||
vin-supply = <&vcc3v3_sys>;
|
||||
};
|
||||
|
||||
vcc3v3_sys: vcc3v3-sys {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc3v3_sys";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&dc_12v>;
|
||||
};
|
||||
|
||||
vcc5v0_sys: vcc5v0-sys {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc5v0_sys";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
vin-supply = <&dc_12v>;
|
||||
};
|
||||
|
||||
vcc5v0_usb: vcc5v0-usb {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc5v0_usb";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
|
||||
vin-supply = <&dc_12v>;
|
||||
};
|
||||
|
||||
vcc5v0_host: vcc5v0-host {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc5v0_host";
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
gpio = <&gpio2 RK_PD0 GPIO_ACTIVE_HIGH>;
|
||||
vin-supply = <&vcc5v0_usb>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vcc5v0_host_en>;
|
||||
};
|
||||
|
||||
pcie30_avdd0v9: pcie30-avdd0v9 {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "pcie30_avdd0v9";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <900000>;
|
||||
regulator-max-microvolt = <900000>;
|
||||
vin-supply = <&vcc3v3_sys>;
|
||||
};
|
||||
|
||||
pcie30_avdd1v8: pcie30-avdd1v8 {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "pcie30_avdd1v8";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
vin-supply = <&vcc3v3_sys>;
|
||||
};
|
||||
|
||||
vcc3v3_pcie: vcc3v3-pcie {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc3v3_pcie";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
gpio = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
|
||||
vin-supply = <&dc_12v>;
|
||||
};
|
||||
|
||||
vcc3v3_m2: vcc3v3-m2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc3v3_m2";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
gpio = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
vcc1v8_m2: vcc1v8-m2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc1v8_m2";
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&vcc1v8_m2_pin>;
|
||||
gpio = <&gpio1 RK_PD2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
vcc3v3_minipcie: vcc3v3-minipcie {
|
||||
u-boot,dm-pre-reloc;
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc3v3_minipcie";
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
enable-active-high;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
|
||||
vin-supply = <&vcc5v0_sys>;
|
||||
};
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
u-boot,dm-pre-reloc;
|
||||
phy-mode = "rgmii";
|
||||
clock_in_out = "output";
|
||||
|
||||
snps,reset-gpio = <&gpio2 RK_PD1 GPIO_ACTIVE_LOW>;
|
||||
snps,reset-active-low;
|
||||
/* Reset time is 20ms, 100ms for rtl8211f */
|
||||
snps,reset-delays-us = <0 20000 100000>;
|
||||
|
||||
assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
|
||||
assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
|
||||
assigned-clock-rates = <0>, <125000000>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gmac1m1_miim
|
||||
&gmac1m1_tx_bus2
|
||||
&gmac1m1_rx_bus2
|
||||
&gmac1m1_rgmii_clk
|
||||
&gmac1m1_rgmii_bus>;
|
||||
|
||||
tx_delay = <0x4f>;
|
||||
rx_delay = <0x26>;
|
||||
|
||||
phy-handle = <&rgmii_phy1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio0 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&gpio1 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&gpio2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&gpio3 {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&grf {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
status = "okay";
|
||||
u-boot,dm-pre-reloc;
|
||||
|
||||
rk809: pmic@20 {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
compatible = "rockchip,rk809";
|
||||
reg = <0x20>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
||||
|
||||
pinctrl-names = "default", "pmic-sleep",
|
||||
"pmic-power-off", "pmic-reset";
|
||||
pinctrl-0 = <&pmic_int>;
|
||||
pinctrl-1 = <&soc_slppin_slp>, <&rk817_slppin_slp>;
|
||||
pinctrl-2 = <&soc_slppin_gpio>, <&rk817_slppin_pwrdn>;
|
||||
pinctrl-3 = <&soc_slppin_gpio>, <&rk817_slppin_rst>;
|
||||
|
||||
rockchip,system-power-controller;
|
||||
wakeup-source;
|
||||
#clock-cells = <1>;
|
||||
clock-output-names = "rk808-clkout1", "rk808-clkout2";
|
||||
//fb-inner-reg-idxs = <2>;
|
||||
/* 1: rst regs (default in codes), 0: rst the pmic */
|
||||
pmic-reset-func = <0>;
|
||||
/* not save the PMIC_POWER_EN register in uboot */
|
||||
not-save-power-en = <1>;
|
||||
|
||||
vcc1-supply = <&vcc3v3_sys>;
|
||||
vcc2-supply = <&vcc3v3_sys>;
|
||||
vcc3-supply = <&vcc3v3_sys>;
|
||||
vcc4-supply = <&vcc3v3_sys>;
|
||||
vcc5-supply = <&vcc3v3_sys>;
|
||||
vcc6-supply = <&vcc3v3_sys>;
|
||||
vcc7-supply = <&vcc3v3_sys>;
|
||||
vcc8-supply = <&vcc3v3_sys>;
|
||||
vcc9-supply = <&vcc3v3_sys>;
|
||||
|
||||
pwrkey {
|
||||
status = "okay";
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
pinctrl_rk8xx: pinctrl_rk8xx {
|
||||
u-boot,dm-pre-reloc;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
|
||||
rk817_slppin_null: rk817_slppin_null {
|
||||
pins = "gpio_slp";
|
||||
function = "pin_fun0";
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
rk817_slppin_slp: rk817_slppin_slp {
|
||||
pins = "gpio_slp";
|
||||
function = "pin_fun1";
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
rk817_slppin_pwrdn: rk817_slppin_pwrdn {
|
||||
pins = "gpio_slp";
|
||||
function = "pin_fun2";
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
rk817_slppin_rst: rk817_slppin_rst {
|
||||
pins = "gpio_slp";
|
||||
function = "pin_fun3";
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
};
|
||||
|
||||
regulators {
|
||||
u-boot,dm-pre-reloc;
|
||||
vdd_logic: DCDC_REG1 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <500000>;
|
||||
regulator-max-microvolt = <1350000>;
|
||||
regulator-init-microvolt = <900000>;
|
||||
regulator-ramp-delay = <6001>;
|
||||
regulator-initial-mode = <0x2>;
|
||||
regulator-name = "vdd_logic";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_gpu: DCDC_REG2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <500000>;
|
||||
regulator-max-microvolt = <1350000>;
|
||||
regulator-init-microvolt = <900000>;
|
||||
regulator-ramp-delay = <6001>;
|
||||
regulator-initial-mode = <0x2>;
|
||||
regulator-name = "vdd_gpu";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_ddr: DCDC_REG3 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-initial-mode = <0x2>;
|
||||
regulator-name = "vcc_ddr";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdd_npu: DCDC_REG4 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <500000>;
|
||||
regulator-max-microvolt = <1350000>;
|
||||
regulator-init-microvolt = <900000>;
|
||||
regulator-ramp-delay = <6001>;
|
||||
regulator-initial-mode = <0x2>;
|
||||
regulator-name = "vdd_npu";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-on-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdda0v9_image: LDO_REG1 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <900000>;
|
||||
regulator-max-microvolt = <900000>;
|
||||
regulator-name = "vdda0v9_image";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdda_0v9: LDO_REG2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <900000>;
|
||||
regulator-max-microvolt = <900000>;
|
||||
regulator-name = "vdda_0v9";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vdda0v9_pmu: LDO_REG3 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <900000>;
|
||||
regulator-max-microvolt = <900000>;
|
||||
regulator-name = "vdda0v9_pmu";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <900000>;
|
||||
};
|
||||
};
|
||||
|
||||
vccio_acodec: LDO_REG4 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-name = "vccio_acodec";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vccio_sd: LDO_REG5 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-name = "vccio_sd";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc3v3_pmu: LDO_REG6 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-name = "vcc3v3_pmu";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <3300000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcca_1v8: LDO_REG7 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-name = "vcca_1v8";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcca1v8_pmu: LDO_REG8 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-name = "vcca1v8_pmu";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-on-in-suspend;
|
||||
regulator-suspend-microvolt = <1800000>;
|
||||
};
|
||||
};
|
||||
|
||||
vcca1v8_image: LDO_REG9 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-name = "vcca1v8_image";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_1v8: DCDC_REG5 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-name = "vcc_1v8";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc_3v3: SWITCH_REG1 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-name = "vcc_3v3";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
vcc3v3_sd: SWITCH_REG2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
regulator-name = "vcc3v3_sd";
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
vdd_cpu: tcs4525@1c {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
compatible = "tcs,tcs452x";
|
||||
reg = <0x1c>;
|
||||
vin-supply = <&vcc5v0_sys>;
|
||||
regulator-compatible = "fan53555-reg";
|
||||
regulator-name = "vdd_cpu";
|
||||
regulator-min-microvolt = <712500>;
|
||||
regulator-max-microvolt = <1390000>;
|
||||
regulator-init-microvolt = <900000>;
|
||||
regulator-ramp-delay = <2300>;
|
||||
fcs,suspend-voltage-selector = <1>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-state-mem {
|
||||
u-boot,dm-pre-reloc;
|
||||
regulator-off-in-suspend;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&i2c0_xfer {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcfg_pull_none_smt {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie30phy {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie30_phy_grf {
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&pcie3x2 {
|
||||
u-boot,dm-pre-reloc;
|
||||
vpcie3v3-supply = <&vcc3v3_pcie>;
|
||||
reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
|
||||
status = "okay";
|
||||
rockchip,bifurcation;
|
||||
};
|
||||
|
||||
&pcie30phy {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
u-boot,dm-spl;
|
||||
pmic {
|
||||
u-boot,dm-pre-reloc;
|
||||
pmic_int: pmic_int {
|
||||
u-boot,dm-pre-reloc;
|
||||
rockchip,pins =
|
||||
<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
|
||||
};
|
||||
|
||||
soc_slppin_gpio: soc_slppin_gpio {
|
||||
u-boot,dm-pre-reloc;
|
||||
rockchip,pins =
|
||||
<0 RK_PA2 RK_FUNC_GPIO &pcfg_output_low_pull_down>;
|
||||
};
|
||||
|
||||
soc_slppin_slp: soc_slppin_slp {
|
||||
u-boot,dm-pre-reloc;
|
||||
rockchip,pins =
|
||||
<0 RK_PA2 1 &pcfg_pull_up>;
|
||||
};
|
||||
|
||||
soc_slppin_rst: soc_slppin_rst {
|
||||
u-boot,dm-pre-reloc;
|
||||
rockchip,pins =
|
||||
<0 RK_PA2 2 &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
usb {
|
||||
u-boot,dm-pre-reloc;
|
||||
vcc5v0_host_en: vcc5v0-host-en {
|
||||
u-boot,dm-pre-reloc;
|
||||
rockchip,pins = <2 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
|
||||
vcc1v8-m2-pin {
|
||||
u-boot,dm-pre-reloc;
|
||||
vcc1v8_m2_pin: vcc1v8-m2-pin {
|
||||
u-boot,dm-pre-reloc;
|
||||
rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pmu_io_domains {
|
||||
status = "okay";
|
||||
pmuio2-supply = <&vcc3v3_pmu>;
|
||||
vccio1-supply = <&vccio_acodec>;
|
||||
vccio3-supply = <&vccio_sd>;
|
||||
vccio4-supply = <&vcc_1v8>;
|
||||
vccio5-supply = <&vcc_3v3>;
|
||||
vccio6-supply = <&vcc_1v8>;
|
||||
vccio7-supply = <&vcc_3v3>;
|
||||
u-boot,dm-pre-reloc;
|
||||
};
|
||||
|
||||
&pmucru {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pmugrf {
|
||||
u-boot,dm-pre-reloc;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart2 {
|
||||
status = "okay";
|
||||
};
|
||||
Reference in New Issue
Block a user